Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi guys,
I am using nRF5 SDK for Mesh v4.2.0 and I implemented this simple message model which can enable the communication between LPN and server node. After my nodes are...
Hi everyone, I see in nRF5 SDK 16.0.0, a Button/Led/Timer assign for handler, like that: bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler); Or: app_timer_create...
Hello,
I was working on buttonless dfu feature. I add buttonless dfu service as shown as ble_app_buttonless_dfu example and i manage to perform a ota dfu on nrf52 devkit...
Dear Sir.
Moving to version 2.4.99 from version 1.2.0 .
In previous version SPI worked well , cs was configured in overlay as
&spi3 { status = "okay"; compatible...
Hi,
I was evaluating FOTA on nRF5340 as possible upgrade to 52 series. All went good which I'm happy of.
However application size is limited roughly to half flash size...
Dear Community;
We are trying to send data via Lora using a nRF9160. The Lora transreceiver we are using is a RFM95W(Semtech SX1272). There are samples of code to receive...
Hi all,
I'm trying to set up my nRF52840 Dongle as a BLE Sniffer. I've followed the setup instructions from "nRF Sniffer for Bluetooth LE-- User Guide" v3.2, and I'm using...
Hi DevZone Team,
Is there a way to stop the ZigBee network steering after a device has successfully joined instead of waiting for the timeout to expire?
Thanks
Which nrf5340 BLE examples build and run? I've tried several and get build errors on everything I've tried.
This is for both the app and net processor.
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my problem was the code running fine but after a while it will go...
Hi,
I am using w25q16 serial flash spi memory with nrf52832.
the flash memory is working fine with all analog input pins(2,3,4,5,28,29,30,31).
but due to the hardware...
sdk version:nrf5_SDK_for_Mesh_v5.0.0_src
in example/light_switch
I use the ios nrf mesh app as a provisioner and at the network layer
I can scan and find nrf5x...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
Dear Nordic Technical Support Team,
I am developing a Mesh consisting of a client requesting to a net (group) of server nodes some motion data (which triggers automatically...
