I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Recently I received the nRF5340-DK. I tested and it was working correctly and as a test, I compile one of the ready solutions of NRF5340 of SEGGER Embedded Studio. Everything...
Hi, I am getting an error 19 which causes a reset after some time running a modified version of the ble_nus peripheral example may someone guide me on how to sort the issue...
Hi, what is the nRF52DK UART, for the nRF52832, flow control when using the ble_app_uart_pca10040_s132 example? It appears to be possible interrupt driven based on data received...
So ...
I'm still trying to get peripheral_uart running.
I'm using a nRF53 PDK (PCA 10095 - rev 0.8.0) (I've received two 0.11.0 boards, both of which died).
I'm using...
I'm using the nrfx twim driver along with Zephyr. I'm using the NRFX_TWIM_EVT_DONE to initiate a subsequent TWIM command and finding that the second command fails due to the...
Dear community,
I was working with a modified code based on an example for switching the leds on/off in a Mesh BLE network. Everything was working well until I tried to...
hello Nordic
i am using nrf52840, SDK16.0, a project build on the peripheral app_ble_blinky example
i am trying to use QSPI but the write function falls on error no...
Hello together,
I try to get the asset_tracker_v2 up and running on the thingy:91.
At the moment I get an Error from AWS_iot aws_iot: mqtt_connect, error: -116
My problem...
Hi Nordic,
I am trying to use the nrf52840 to talk with my 4G module on baud rate of 115200 , but I find it always come into error for the recving the uart data. Also it...
Hello,
I have an nRF9160 development kit and was measuring the time it takes for switching off the modem
when it has an open data connection.
I did it by sending an...
Hi,
I'm currently working on NRF52832 (Softdevice s132 6.1.0) controller and developed a firmware from light switch client to develop a mesh network and its working fine...
Hi sir,
I have downloaded the NORDIC THINGY52 SDK from the given link https://devzone.nordicsemi.com/f/nordic-q-a/51236/unable-to-compile-ses-project-in-thingy-52-sdk (As...
Hi,
What do I need to be able to FOTA when nRF Connect SDK is updated?
For example, when the SDK version is 1.6.0, can I use the changes I made to the new SDK version...
Hi, as the table register above, If I want to set Tx_Gain manually, Does MODE effect my config? (Ex, if I choose mode as 0, does the device use POUTA default to use instead...
Hallo,
I am trying to communicate MAX86140 sensor with nrf52840DK. This is the link to the datasheet of MAX86140/1 . I am able to write and read MAX registers successfully...
