I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
We are working with the nRF54L15 using nRF Connect SDK v2.8.0 and would like to enable the secure boot feature.
However, it appears that the SMP Server sample in...
I'm using put all together 2 sample
a) NUS Uart that is used for the configuration;
b) zephyr/samples/net/opentread/coap Using the nrf5340dk/nrf5340/cpuapp.
The compilation...
Hello,
Step 5.2 of this part of the course has a code example which shows which i2c node to use to control the temperature sensor. In the case of the nRF54l15DK it is...
Hello Nordic team,
We are using an nRF5340 as the host processor, and an nRF9160 module is mounted on top of it. All LTE modem AT commands are sent from nRF5340 to nRF9160...
I'm trying to implement the NRF5340 as an I2C slave. The current answers all show the answer as old to look for a newer answer. Were implementing the NRF5340 as a slave to...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
I am currently working with the Aliro 1.0.0 from nRF Door Lock and Access Control Add-on.
I need to know how to properly configure or set custom data fields for Aliro protocol...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
I am attempting to get familiar with the NDEF support on the nRF54L15 DK. After creating a copy of a sample based on the WRITABLE_NDEF_MSG example, I create a build configuration...
Hello Nordic Support Team, I am developing BLE content, where nodes will be periodically uploaded to the gateway.During this interval,the CPU needs to be kept idle, waiting...
Hello DevZone,
I have wrote a standard Zephyr display driver for one customer, I used sQSPI and Zephyr MSPI API.
I finished the development, but the QSPI (1-1-4 mode)...
Hello,
Our product (sports timing) will be used at the upcoming Olympics and our customer is being asked some questions about wireless specs. We use Bluetooth 5 (backward...
Hi,
I have a custom nRF52832 PCB with 10 buttons connected to various GPIOs. All buttons work correctly except the two connected to P0.07 and P0.08 they produce no response...
Hi,
“ We are designing our board with the nRF54LM20, and both the SPI/QSPI and UART peripherals can operate independently and be mapped to separate GPIOs.in QFN-52 Package...
