Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi all
I'm using nrf52805 soc, softdevice s112 , sdk version 17.0.2 and nrf connect mobile app for my project development. I can connect and disconnect the nrf52 device...
Hi,
I am using P0.10 GPIO of nRF52840 (QFN package) as an output for driving a transmission circuit with an 8MHz digital signal.
According to the datasheet this pin is...
Hi team, I'm using Mesh in my project. Using this thread as a reference, I tried to decrease the data throughput and experiment to see if devices could communicate with each...
hello,
i want to know if is possible have Multilink, ble Uart and relay together? it is for make an a type of Mesh network of 4 devices with a BW of 1Mbps (see the image...
Hi
I'm testing the SLM application in nRF Connect SDK ver 1.3.1 on nRF9160 PDK ver 0.8.2 using the LTE Link Monitor v3.5.0
Giving the following commands, the UART stop...
hello ,
i am working on recieving data from sensor using nrf52832 with time and data right now i am getting time that is set by me my problem is i have to set time automatically...
Here is an issue I am having when using MQTT in a poor (RSRP < 15) LTE signal environment
Condition:
nRF Connect SDK v1.3
modem firmware v1.2
TLS Socket is configured...
I've worked through the Custom BLE Service example ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) and I'm attempting to port it to C++ to form the...
Hi,
I need to write a linker (ld) script for our nRF52 application. Essentially I need to combine the linker script that we already use with the scripts that exist in the...
trying to build a long range coded phy broadcast/scanning application. as I know zephyr doesn't support that so we have to include nordic link layer based on this post
https...
Hello all,
i am using ble_app_uart example.I add the line
in the begining of the main function. All the ble connection works, but putty shows strange characters...
I am having a bit of trouble getting high enough data throughput for my application so I have a few questions regarding it.
Can running the spi/other peripherals affect...
Hi，
I tried to build a BLE sniffer environment. And it works well to capture the LE secure connection air packet after Eable Secure Connections debug mode （uses the debug...
Hi,
using:
SDK for thread and Zigbee 4.1.0
NRF52840dk
I am trying to add UART (for my custom application) to an existing Thread example with CLI. (e.g. ble_thread_dyn_hrs_coap_srv_freertos...
