Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
HI,
I'm reading this post about NFC antenna matching. It says in Method 1 to connect the coil antenna to the S11 port of the network analyzer. How should I make the connection...
I am currently working on a design with the nRF9160, and have a few questions about the DEC0 pin and decoupling for the module in general. I have been considering adding additional...
I keep seeing this in your documentation:
This functionality is in the process of being deprecated and replaced by Zephyr’s default devicetree-based memory partitioning...
Hello Nordic Team,
I am evaluating the nRF54LM20B physical DK using nRF Connect SDK v3.3.0‑preview2 . In the SDK, only the nrf54lm20apdk board target is available, and BLE...
Hello, I am working with the following sample project and NRF Connect SDK v3.3.0. (Referenced regarding this topic .) The sample implements DFU with MCUBoot while using the...
I am evaluating the output power of a testboard that uses the nRF52840-QFAA.
The matching network closely resembles the recommended network in the datasheet (shown in figure...
Hi!
I am using MCUBoot and the DFU library to perform a custom firmware update (which is working as expected).
I have a question about the "swap_type" value, which is...
Hi Nordic team,
I’m seeing a repeatable configure hang with NCS v3.3.0 sysbuild on macOS. The visible build output stops after:
After inspecting the process tree, CMake...
Hi Team,
I need to use this external clock for my deep sleep use case so let me know the step forward for the same.
I am using custom board with nRF54L15 and also LXFO...
HI all,
The main program suddenly encountered assert （nrfx_grtc.c line 278）while running, which happened by chance. The following are the relevant logs
note:nrf54l15...
Hi, all!
I'm currently facing an issue with upgrading the nRF52840 firmware on a Thingy91 and would greatly appreciate your guidance. I'm following the official instructions...
Hi everyone, I recently encountered an issue while developing with the nRF54LM20A. When acting as a USB High-Speed (HS) HID mouse device, Endpoint 0 fails to respond with...
Hi,
I started from your
Bluetooth Mesh NLC: Lightness Controller/Energy Monitor sample
and I tried to insert a Light CTL Server model in the project.
After a lot of...
Hi,
I am using the Nordic UART Service (NUS) on an nRF52840 with NCS. Without pairing enabled, NUS works perfectly with the nRF Toolbox UART service — both sending and receiving...
