Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I am using the Nordic SDK 15.3 for nrf52832 development board. I am using SES as my development environment but I am unable to get RTT logging to work.
I have enabled RTT...
I am using SPIM3 to drive a peripheral, only using tx. And I noticed that SPI is sending wrong/corrupt bytes once in a while. See below image where the code tries to send...
I am developing a multi-peripheral product that knows all the possible connectable central Bluetooth device addresses (centrals are all NFC enabled smartphones).
When a...
I am using QSPI of nRF52480 with freqency 2M Hz. Now I want to reduce to 1M Hz,
but QSPI_CONFIG_FREQUENCY min value is 15
// <o> QSPI_CONFIG_FREQUENCY - Frequency divider...
Hi,
We are working to build our own SPI module code on nRF52832 in Segger IDE without Using SDK. But we are stuck at this point of error in core_cm4.h.
Unknown Type name...
i am trying to use flash to store and read data. I am able to do that when there is only softdevice and application. but when there is bootloader code get stuck. softdevice...
hello everyone,
In my application single central(ble_app_uart_c) scanning check each peripheral(ble_app_uart) Mac id which peripheral mac id defined by central established...
Dear DevZone community,
I'm developing a Mesh application using nRF52840, I'm developing with both the Nordic development kit (BOARD_PCA10056) and USB dongle (BOARD_PCA10059...
Hi,
I have tried changing the connection parameters (min and max connection interval) and looked into nRFGo Studio to see what the current consumption would be. In Column...
Hi Nordic Team/Fellow developers,
I wanted to understand how you guys made sure BLE stack/application is working properly? Like, how did you guys debug your application...
(SES + SDK15) Hi! I am trying to create an new firmware prototype based on ble_app_template_sample Until now I have a connectable firmware, with one service and several characteristics...
Hello, I have simple custom board with simple firmware. It's just nrf52811 advertising with 0,5 s interval. I'm considering to use Long Range advertising, but wonder how it...
Hello,
if I want to use the Nordic crypto library, I include all nrf_crypto_xx .c files. While compilation, I get in IAR an error:
"explicit type is missing ("int" assumed...
hi
i am using the nrf52832 board.
I am trying to build the ble_app_template code but i am geeting the following build error
.\_build\nrf52832_xxaa.axf: error: L6050U...
