Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Using Rowley Crossstudio for ARM.
Using SDK V15.3.0 and S140 V6.1.1
When calling sd_softdevice_enable(..) it returns 0x1001 ( SVC handler missing ). Any suggestions ?
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
At present, I have a project that needs to add dual uart function, but 52832 does not have hardware dual uart function, so I need to simulate one serial port, I need your...
Hi all. I try to implement ble dfu bootloader project via getting start from SDK/examples/dfu/secure_bootloader/pca10056_ble_debug project.
Using:
OS: Linux
Compiler...
Hi!
This is a general question about iOS app distribution, but it regards our use of Bluetooth Mesh. I know it is each company's own responsibility to make sure they comply...
Hi there,
I am porting existing code from nRF52832 to nRF52840, and found that bootloader references to NRF_BPROT fail:
Apparently becuse the nrf52840.h in the mdk does...
Hi All,
I have loaded in the Bluetooth Mesh Light-Switch example and it works well.
For now, I would like to read out the received data from the switch node (client) to...
Hello! I am using SDK 15.3.0 to develop the NRF52832 firmware. At present, I want to implement a function, when the device is connected to the IOS host, start pairing, and...
hi attached code for below requirement:
command: scan on - scan devices
command: devices - display filtered devices .
Filters set are for : thermometer, NUS and custom...
I am using the TWI manager to schedule transactions with a number of sensors, over two seprate twi instances, and then sending that data over Ant.
The twi manager scheduling...
I am using the NRF52832 chip on a D52M M8 module, and SDK 15.2.
I have a number of sensors that I am communicating with over TWI using the TWI Manager on two separate channels...
Hey
I am working on ble_app_blinky central and peripheral, I want to calculate the RSSI of peripheral after connection with central. I am able to calculate the RSSI value...
At the end of last year, the new package nRF5240 WLCSP was delivered and it is now available in the market, however, I have not found an official layout for this new package...
