Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello all,
I am right now working on one project. where i use nrf52832 BLE board. right i am doing i2c communication of temperature sensor(lm6bd) with ble board. but can...
Hello All,
I am using nRF52810 programming in segger embedded studio in windows 7. i am trying to do i2c communication between sensor and nRF52810.i am create custom service...
Hi,
I have a question about direct advertisment - if I direct advertise to one android, then other devices won't show it am I right? How does this direct advertising works...
Hello all,
I am using nRF52810 programming in segger embedded studio in windows 7. I am refer SDK nRF5 v5.2.0. I am trying to do i2c communication between sensor and nRF52810...
I had a couple of questions regarding the SPI slave peripheral on NRF52:
What is the behavior of the peripheral if a transaction completes (NSS goes high) and another...
I used the example code of MQTT pub and sub with nRF52 DK which has nRF52832 in it. I have sent the data from one kit to another with the help of Raspberry pi 3 as a router...
Hello. I need a bit of help with my case. I have nRF52832 dev kit. I have set heap size to zero in Makefile:
And even with that change I am still able to allocate memory...
Hello,
I have some questions about NFC on nRF52832:
1.Could NFC on 52832 works as a card reader , for the mifare 1 card, or named S50 card?
2.In the example "nRF5_SDK_15...
Hi all,
I have read that ANTUSB-m is needed for ANTWARE running in Windows PC. Can I use nRF52840 DK or nF52840 USB dongle in place of ANTUSB-m? If yes, where I can find...
Hi all
I have a custom Board, I have tested it a lot. NRF51822, programed with Mbed..
In general the Software and Board WORKS FINE, but I found some problem in my procedure...
Hello
I am following example on :
examples/dfu/secure_dfu_test_images/ble/nrf52832
when flashing:
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hello,
I'm trying to use this code https://github.com/kimyd/SHT1X_on_nrf51822 to communicate with an SHT11 sensor via GPIO pins. I have a Saleae hooked up an can see the...
Our project uses nRF51822 with SDK12.3.0 and s130. We are using app_timer_appsh.h and app_scheduler.h to make a "UTC timer" by counting a static variable each 1S timeout ...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
when I debug the pairing function,the phone displays one dialog box about Bluetooth...
