In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I use the app_gpiote_user_register to set GPIO port 1 pin, but this registers only 32-bit mask, so it can only to setting port 0.
If I want to use the port 1 pin for app_qpiote...
Hi!
I'm attempting to run the application from this URL , but nothing appears on the serial console, and I don't see any posts on the toilet website.
Could you help me...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hello! Recently while performing a BLE firmware update using the mcuMgr Library, the stages of the firmware update are as follows VALIDATE, RESET, and fail on UPLOAD. When...
the code below successfully complies and returns 3 services with 1 characteristic each, I have copied the uuid for the primary services and characteristic and that doesn't...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
Hi,
After downloading any of the projects from nordic github, how does one compile the project successfully? Where should i extract the files to and what paths should i...
HI.
NRF connect For Desktop Programmer program Fail.
So I used command Tool (nrfjprog). command Tool worked.
Enviroment:
- nRF Connect For Destop v5.1.0
- Programmer...
We're attempting to provision one of our nRF9160-based IoT devices to our AWS VPC.
We're following this procedure:
Provisioning our eDude on AWS
Step 1: Provision the...
I'm trying to get FOTA updates working on the NRF54L15 DK. I noticed there isn't a dedicated guide available for these yet so have been using this page: https://docs.nordicsemi...
I’m encountering a build issue with Zephyr (version 3.7.99) on my custom board based on the nRF52840 SoC. The build process fails during the linking stage with an undefined...
Hi ,
We are using MCU nRF52832-QFAA-R (Flash 512KB & RAM 64KB) with softdevice s132 - 6.0.0.
I am not sure what is extracly Soc Revision of the MCU ? But I read some information...
I have a custom SMP handler that uses an SPI transport. If I use the pin reset to reset the module after programming sometimes the module hangs when calling that handler....
Hi We would like to use the nRF5340 with a custom network core image that runs the full Bluetooth stack and I have gotten it to work with sysbuild. However, we would like...
