Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi,
I am trying to program a custom board containing an nRF9151-LACA using the external programming interface (P20) on an nRF9151 DK. The board has never been programmed...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a eval setup where I use the nrf52840 dongle with hci_usb flashed. It has a non-default config to enable DLE (this works fine).
I am sending buffers of 8192 bytes...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi,
I have an application which is developed using nRF5 SDK version 17.1.0
Migrating to nRFConnect SDK is not an option at this stage of the project.
The application...
I'm stuck trying to set my nRF Connect extension on VSC. I've followed the guide for the installation but I'm reaching a wall. Every time I try to install a given SDK I have...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi everyone,
I'm evaluating the nRF54L15 for a very low-power sensor node application powered by a Lithium Thionyl Chloride (Li-SOCl₂) primary cell. The goal is to achieve...
Device : wearable IOT device
Battery capacity : Max 4.2V (Typ. 3.7V)
BLE Tx Power : Tx power is highest when the battery capacity is 4.2V (measured in air, not conduction...
Hi, We want to use Sensibel microphones in a project with nfr9151, and it will be used to sample one microphone (mono) with 24bit data. This microphone seems to require 32...
Hello, Nordic Support!
I have some problems with programming my custom boards using my nRF54L15dk v0.9.1, when I use a setup with long cables (or several cables & adapters...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi guys,
I'm hitting an error with the current Aliro 1.0.0 lib.
When a credential is signed today but its validFrom is in the future (e.g. signed=2026-06-17, validFrom...
