In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi all,
I'm trying to get a UART connection running at 460800 bps, and it fails about 1-5% of the time, meaning that I receive less bytes than I expect. This happens a lot...
Hi,
I want to debug [i.e. attach to and single step] mcuboot [running as second stage bootloader] using Ozone and JLink.
I can connect to the board via the debugger...
Hi! I am trying to sync the time on my nrf9160dk with date_time_now() or date_time_uptime_to_unix_time_ms() but it seems that they return a very low unix_time_ms (only 1089262423ms...
The nRF7002DK board has a Vdd of 1.8 V, unlike every other Nordic board I've seen which use 3.3V. I assume this is due to the nRF5340 errata that state that the QSPI bus ...
Hi,
We are Designing the Long range module using nRF54L15 with nRF21540 FEM.
Now want to use Dual Antenna simultaneously. we have Couple of questions
Please guide us...
Hi all,
I am currently working on a personal project with hundreds of nodes. I have created a device with remote provisioning models (server and client). In my network...
I'm encountering an issue while trying to use the CAF LED module with the nPM1300 PMIC. Despite configuring the Device Tree, prj.conf, and led_state_def.h, I'm still getting...
I would like to confirm if my understanding is correct regarding calculating the average current consumption using the PPK2.
As shown in the image, the Selection Average...
I can't find any mention about MU-MIMO in the datasheet. Does the nRF7002 support MU-MIMO TX and RX?
I cannot find any details of if support is mandatory for a 802.11ax...
Hello,
I need to implement Find My Device for nRF52833.
From Sample I could find "samples/bluetooth/fast_pair/Locator Tag" example. I tried to go through it. but I could...
Hi,
We are using the nrf52833 for development.
The first version of the program can connect to the discovery service normally. But we need to add some new features. And...
Lesson 8 of "nRF Connect SDK Intermediate" DevAcademy course deals with Bootloaders. I've successfully done the exercise of updating firmware using the off-the-shelf mcuboot...
hi,i wanna read the imu sensor lsm6ds3 on board of nrf52840 based Xiao BLE Sense
so i used the code in samples /sensor/lsm6dsl
first i didn't know if i do have to create...
I'm trying to use the nrf_desktop application 100% standard, with NO changes to the codebase at all.
My initial assumption is, that once I flash the nrf52840dongle, it should...
I am working with ESB between 2 nRF5340DK's (w/ no need to be cross compatible w/ other devices) and with NCS v2.5.0. I am using ESB to wirelessly transmit data every 2ms...
