Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Can’t RTT view even provided precompiled code that comes with nRF5 SDK v17.1.0. Tried also the .hex versions that came with older SDK back to 15.3 – same story . Tried even...
Hi - I am trying to use the PCD library in NCS 2.7.0 w/ sysbuild, but this library seems to require partition manager to be enabled (due to the `include <pm_config.h>` in...
Hallo,
is it still true that there is no automated possibility to combine two sdk_config.h files as I read in a several years old post? This is necessary for integrating...
I have a custom board that is in production but is running NCS 2.5.0. I am interested in migrating to 2.7.0 however I am running into a few issues. When I pair to the device...
When I try to build the solution with "Optimize for debugging (-Og)" the linker fails saying `rodata' will not fit in region `FLASH'. FLASH overflowed by 46056 bytes. This...
Hi all.
I have a project on nrf52840 with ble. I needed to add a nrfx timer there. I deleted everything from the main function. Added the code from the timer-counter example...
I'm going to add frequency hopping to ESB
so i have some problem
1、Whether demo is available for learning.
2、for example Gazell frequency hopping ,Where can I see detailed...
Dear Nordic,
I'm unable to register an nRF9161 device on the Verizon Thingspace IoT Network. They have a web UI which allows one to enter an IMEI, ICCID pair. When I enter...
Hi,
We have developed firmware for a custom broad using the nRF52832 with 512kB flash, and our firmware currently uses 48.5% of the flash.
We are using Zephyr and version...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
I am trying to write tests for my code using CppUtest. I know the platform has memory leaks detection support. it seems that everyting is set up correctly to see the results...
