Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hi
using NRF5_SDK 17.0.2
I'm trying to better understand the DFU process, currently have a large number of questions. But mainly i would like to better understand the...
hello
I am watching this video to operate the nRF9160DK. The PIN number was written on the back of the nRF9160, so I skipped the video to 9:36 as instructed at 5:21, selected...
Hello,
My nRF9160 hard faults (i think?) when issuing a command to the modem, specifically this line:
which then calls ncs function:
This leads to I think is...
Hello, I'm trying to run the OpenThread CLI example on the nrf52840 chip of my NRF9160_DK. I've managed to flash the code on the nrf52 and able to see the Zephyr kernel boot...
I have tried various methods from different doccumentations and I couldn't do so. Can you provides some steps to create a west workspace.
Thanks in advance.
In my project, I am planning to use LTE modem and an external flash memory with a file system. I have problems to run code for the non-secure build type. A similar problem...
I've been tinkering for several says to get GNSS working on a Thingy91 with Zephyr.
I've tried the 'location' example and have struggled to register the device on nRFcloud...
Following the instructions to build the sample resulted in an error message ..
Here are the details ... probably something simple but not obvious to me ...
PS C:\ncs>...
Hello Everyone,
I was use Nordic App for Mesh in android to add Telink's chipset into mesh. But after few minutes, telink's device go out Mesh.
I don't know how to add...
Hi,
Iam using "pca10056_s140_ble" secure bootloader example for my project.
FYI. My project gets its new firmware from internet and stores it in BANK1 memory using GSM...
hi Support team,
customer get samples with 9160, but find out they are not able get pin code.
i searched the spec, and at command +CPIN, it is not able to read out the...
Hi,
I've installed ncs manually following this guide: Installing manually — nRF Connect SDK 2.0.99 documentation (nordicsemi.com) and then set the following environment...
Hi,
I have an application using MCUboot (Only for using with serial recovery. No SMP server running in app).
I enable CONFIG_BOOTLOADER_MCUBOOT and parent and child images...
Hi,
I am using nRF5340 DK + NCS v2.0.0 with nrfx backend for SPIM.
For my application I want to trigger a SPIM1 transaction at a fixed interval. To do this, I set up an...
Hello,
I have an issue when trying to use NVS backend for BLE settings with the settings_storage partition in defined external flash region. As we are doing a multi-image...
