Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hi Dev team,
I am using the Thingy91 for my development project. I have noticed 1 peculiar issue and wanted to ask for suggestions regarding it.
I had deployed a Thingy91...
Hello there,
I am that newby in the vs code dev environnement. I use the XM122 from acconeer to perform radar measurement. The soft provide by Acconeer compiles and works...
Dear Community;
I am trying to port this code that was made for an nrf52 to an nRF9160. I have a 4.99K pull-up resistor between the data line and VCC.
This is my ds18b20...
Hi, Is it possible to increase the size of the buffer for the UART IRQ RX function such that it receives more than 8 bytes at each interrupt? Currently I am trying to send...
Hello everyone,
I'm reaching out to touch base on the current support status on the latest software (MFW v1.3.1 and NCS v1.7.1) for CoAP over UDP (DTLS) for using as a main...
Hi,
I have a circuit with an I2C peripheral on a separate power switch. There is excessive power consumption (about 50µA extra) due to leakage after TWIM is disabled and...
Hi,
I am using a nRF9160-SICA-B1 and sometimes will see debug output that looks like this in Tera Term:
Glitch example:
Good example:
Basically it appears like...
Hi everybody,
I'd like to perform serial DFU on my nRF52832/nRF52840 based devices, using an external master MCU. Is there any reference C code for the master MCU? In this...
Hello. I am new to Zephyr. I cann't debug Hello_world sample. As i understand it always reboots and does not go to main.
I am trying to use VS Code and nRF Connect SDK ...
NRF Connect shows no device available.
usb interface MCU which embeds a j link is not detected by windows.
LED5 is blinking.
I have an external jlink to try to recover...
I had a project set up and working with my nrf52840 dev kit. It was using the 1.7.0 SDK and was based on the zephyr hello world sample. Today when I open VS Code, the project...
Hi,
On Segger Embedded Studio when you debug you also get the RTT console displayed at the same time. Is this possible on your VS code implementation? At the moment I can...
I'm trying to add 802.15.4 driver into my project (to implement an proprietary protocol).
The wireless_uart sample is very helpful and I got it up and running.
However...
I can find some other topics about this:
Like this one:
https://devzone.nordicsemi.com/f/nordic-q-a/43370/nrf_log_info-and-printf-does-not-work
or this article:
https...
