Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello,
I am new user for the Nordic NRF528400 microcontroller. I am working on a project that is using the 8 channels of ADCs to get data from sensors. The system is powered...
We are testing our custom board using the the dimming_server example from mesh 5.0 sdk. This example runs fine on the PCA10040 board. On our board, the provision runs normal...
Hi,
I try to add BLE scanning function to receive all the advertising data in my application.
My existing application is started from advertising example.
After added...
Hi, I have a customer wanting to do OTA firmware upgrade using nRFUtil on Fanstel BC840E module.
They have installed the python
D:\nRF_Pjts>python Python 3.9.2 (tags/v3...
Hi!
After cloning a fresh codebase and building the trusted firmware-m sample parts of the mcuboot scripts seem to break:
Traceback (most recent call last): File "/home...
Hi all,
I am developing a low power product based on the nrf52840 module, using the openthread stack from NCS (v1.4.99). Since the device is powered by battery only and...
I would like to use MAGPIO0 , 1 and 2 as 1.8V inputs. I've read through the documentation, but can't find any way to assign pin numbers to these (I'm using Zephyr), only that...
Hi,
First i want to know what is the relationship between connection interval and GAP Event Length.
In one test condition I configured as:
connection interval = 7...
Hi Experts,
We are developing application on nRF52840 based BLE 5.0 module i.e. BMD-340, in short we are integrating the BLE in one of our existing product & upcoming...
Hi Nordic Team,
I'm working with Nordic NRF52832 BLE development Kit. Currently, we are working with DFU Secure bootloader. In this bootloader, we tried the button pressed...
Hello everyone, I am running a code with uart i2c interruption and power management but I have this error : nrf_pwr_mgmt.c:78: undefined reference to `__start_pwr_mgmt_data...
Hi,
Does Nordic have a network-steering function that attempts to join networks on all channels? We will not know which network channel the sensor needs to join ahead of...
Earlier (couple of months) I was working on the examples/peripheral/ppi example in SDK12.2.0. I converted the Keil project inside pca10028/blank/arm5_no_packs to a Segger...
Hello,
I am trying to reset the Zigbee network configuration on my End Device when the user press on a reset button for a long time.
I don't want to restart the product...
Hey.
I have a GPS chip which uses 57600 baud for its rx pin, and 115200 baud for its TX pin.
I need to switch between the two baud rates, and also some times connect to...
