Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi everyone,
I am following the qspi example to communicate with MX25R6435F flash memory. This is my first time interacting with a flash memory and I have some questions...
Hello!
i´m enable ble long range like central for scanner beacons, i can see long range beacons, but only one time, then i need to restart my DK: i use to do this ble_uart_c...
Hello,
As per your given link in 1.2 Build and flash - using SEGGER Embedded Studio ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
Hi,
It appears that at least one Mesh_v4.2.0 example (light switch) will not link under nRF5_SDK_17.0.2.
I managed to get Mesh examples to run under SDK_17.0.0 a while...
I have a new Bluetooth remote product in development that has a bluetooth stack that will incorporate HID, BAS, NUS, ANCS, and buttonless DFU services. I have the HID and...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm getting this error while trying to connect with my device in the "ble_app_hrs_c".
"Connection...
I have found a few "how to" on cofiguring Eclipse for application development on nRF52 devices. After some point things are not as described in this guides. So, Is there any...
I'm trying to create a read event whenever a certain characteristic is read. I used BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event to monitor that. I also set "is_defered_read"...
Hello,
I am developing a composite HID peripheral based on the nRF52840 that can connect to a PC either via USB or BLE.
I am using SDK 15.0.0.
Regardless of the connection...
When I build and run an example Bluetooth: Peripheral HIDS keyboard (it's the same for master branch and v1.3.2) using nRF52840 DK I faced one strange behaviour. To simplify...
I just downloaded the latest version of the pc-ble-driver hoping some of the bugs I had reported were fixed. The downside is the notes do NOT indicate they were addressed...
I'm working on an nRF52840 design where we may get away with only the outer pin row on the package.
However, one pin on the inner row of harder to reach pins seems important...
To the kind attention of Nordic support team,
I'm considering here a scenario where only a device and only an host PC are involved. They are ble bonded together.
Now,...
I have been working on receiving data from sensor using nrf52832 and I have been successful in getting the data and printing the same in the app. I have also been succesful...
Hi!
I am using an ASXL375 accelerometer with a nRF52832, and I am trying to figure out a good way to read the sensor data asynchronously (allowing the other processes the...
