Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
This isn't exactly a question, because after like...8 hours of debugging, I figured it out. However, in zephyr/samples/bluetooth/mesh, it defines a hardcoded device uuid ...
I am using ble_app_blinky_c application for my project. I want to update my central's default MTU size from 23 to 150 and I know my peripheral device supports MTU size of...
hi,
currently i am using maste r(nRF5_SDK_15.3.0_59ac345\examples\ble_centra\ble_app_uart_c) and slave (nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ ble_app_uart ) example...
Hi
After migration from SDK 14.0.0 to 15.0.0 our FW crashes during SPI session
We use EasyDMA , so we use SPIM driver directly without wrapper nrf_drv_spi
The crash...
Hi,
The central part of multirole example is not able to connect to peripheral (other board with ble_app_uart peripheral) and error returned is in the on_ble_central function...
We're using LTE to communicate somewhat large data packets over MQTT, and we'd like to build in some robustness in case the link goes down or a publish fails to receive an...
as soon as I built and run my firmware program on SES ARM 4.22, RF connect scanner can find the ble device (NRF52832). But after 10 seconds later, i do rescan in RF Connect...
Hi, I need to activate uart on pca10059 i can't find where pin TX and RX in pca10059. i already read the schematic and try uart example but end up with can't send or receive...
