Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
I built this ( devzone.nordicsemi.com/.../Nordic_2D00_Thingy52_2D00_FW_2D00_master.zip) Nordic Thingy SES project and downloaded the generated hex file in Nordic Thingy. Now...
Hello,
I tried to build the mesh sdk in all way.
Please help me or send me the sdk set-up which is without error.
I tried by sdk15.3.0, sdk15.2.0 and mesh sdk. Try...
Hi,
I am having problems with using BLE along with gpiote and ppi for measuring the delay between two waveforms and sending the delay between them to an app using bluetooth...
Hello,
I have recently built and flashed CoAP Sample on my board.
After that the device cannot connect to the mobile network.
Could you please provide me a description...
Hello,
We have finished the development of a prototype device that incorperates the nRF9160 SiP. I would like to know if there is anything I need to set-up in the device...
Hi,
I would like to use hal_time_get() [hal_timer.h] in my project, and I try to add below library into Makefile.
but I got an error. "error: implicit declaration of function...
i am using/ ble_app_multilink/ example present in central folder..i am beginner to this ,,so i have few doubts in it
1)so where actually advertisers(which are advertising...
Hi,I had a problem with nRF51822 DFU.I tried to OTD nRF51822( version SDK_9.0.0 s110 ) wiht Android 9.0 devices( nRF tool version 1.9.0 ),but it always fail at 1%.The problem...
Hello fellow Nordic-ians,
I am developing a custom firmware for Nordic Thingy 52. I am using the Segger Embedded Studio as my IDE and J-link Edu Mini as the programmer ...
Hi,
I have found zboss 1.0 opensource.
Surveying the source, i have noticed that variable "g_zb" (nicknamed by ZG) give system informations.
I can find zed address(16bit...
Hi,
Here is my setup, NRF52832 PCA10040 s132, sdk 13.0.0.
I work on Windows 10 with a server (The aim is to do it from a Raspberry later) which one is connected to my...
Hi,
I'm developing a simple sensor application using s132 on NRF52832_XXAA. The application works fine, except that I have problems disabling the saadc module after conversion...
