Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Over the past 2 weeks the programmer fails to recognize my9160DK board. Instead, I see it listed as "J-Link" in the device list with a serial number underneath. The programmer...
Hello! I am discovering a new approach to nRF52 development. I used to be quite happy with SDK+Segger Embedded Studio. But as I understand it, this is an outdated method....
I can't figure out how to run sample code that uses the LTE-M modem.
I see nrfxlib has a modem library. But I don't know how to make a simple sample app that uses this...
Trying to build and flash the nRF5340 Audio application to my nRF5340 audio DK eval boards for eval purposes. Apparently this requires access to the LC3 repo so I am seeking...
Can you share the source impedance measurement for the nRF52840-CKAA? Is the T-network only for impedance matching? Do i need a filter for harmonics if I'm planning to transmit...
I'm using the pc-ble-driver-py: Standard Heart Rate example to read a characteristic just fine.
My issue is i now need to write a to a characteristic.
How would I do that...
Hi
I've recently been working on the ncp host example provided by nordic. after downloading the standalone version from the site, I tried programming the 2 nRF 52840 dk...
nRF SDK 17.1.0 with SD140 7.2.0
There is no example for how to use the sd_rand library. I've seen scant few posts that mention functions like sd_rand_application_bytes_available_get...
Hi I've just started developing with the nrf52840 and Ive been following the official documentation on how to use the programmer shipped with nRF Connect.
Unfortunately...
Hi,
In a custom nrf52840 board (DC/DC=on, LFCLK=RC, CONFIG_SERIAL=n), using ncs2.1.0, I measure through PPKII ~6.7uA in system_off mode, which is reasonable.
In system_on...
I have a similar question as in the previous post (about 4 years ago) with title "nRF52 WLCSP DCC routing - - ok to run over GPIO pins?" by Laserdan, i.e., I would like to...
Hi there,
The spec for nRF52840 says in sec 6.33.1 that for UART, "The external crystal oscillator must be enabled to obtain sufficient clock accuracy for stable communication...
Hi,
How do you export your project from nRF Connect within VSC? You may have modifications you did for DTS files, prj.conf etc, that you may miss if you focus on just src...
Hello,
The documentation for the nRF5340 says that the UICR OTP registers can only be written to a non-0xFFFF value a single time: > Can only be written to a non 0xFFFF...
