Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
in the nRF52840, SPIM3 allows for high speed >4MHz communication. But I cannot see if there are dedicated pins specific to this mode, or can i map any pin to the SPIM3 high...
Hi Team,
As part of our requirement we need to fix the Advertisement to one fixed channel instead of altering between 3 channels like 37,38 and 39. If we have any sample...
Hello,
Using own BLE stack here (not SoftDevice) and having troubles with LL certification test cases with particular problem:
the tester establishes connection and...
Hi,
I would like to take current & power measurements of the nRF52833 SoC with the desired firmware file flashed to it. I am testing an application that uses the CPU temperature...
We are trying to make it so that we can permanently make one channel on the BLE module only for advertising while having the other channels flexible for other needs.
Hello, I have nrf52DK (nrf52832-PCA10040) and I wanted to test the Peripheral example in the nrf Connect SDK. I have built the project for nrf52DK_nrf52832 and then flashed...
Hi,
I am developing app using ant softdevice s212. I want nrf52832 to enter system off and stay there until interrupt from sensor occures. This interrupt is connected with...
I use nrf5340 to build esb project, I use the following code to scan rssi of different channels, but I read the value of NRF_RADIO->EVENTS_RSSIEND is 127, I hope you can tell...
Dear ,
How do I enable DCDCEN mode if I am using NCS1.8.0 SDK? Is there any Kconfig setting I need to perform to make this available?
Thanks and regards, Kevin
Hi,
Just wonder does NVS only use half of the configured size? I have configured the nvs_storage size = 0x2000 ( 8192 bytes)
So sector_count = 2 (4096 / sector)
When...
Hi Team,
We are in process of developing pairing mechanism for our peripheral device. We are considering using NFC for OOB. Here is what we think we should be doing: ...
Hello People,
I am working on a custom board and while trying ble_app_uart example code instead of the advertising name given in the code the device was showing "DFU_TARG...
Per the documentation on multi image builds , a child image folder that contains a <board>_<revision>.overlay it will be merged with BOARD.dts but I cannot do the same for...
Hi,
I'm working on a project that utilize the MAC library.
Coordinator with non-beaconed mode was previously used in the project, however the NRF 17.1.0 SDK is not compiled...
What is the threshold voltage on a nRF52840 GPIO to detect low level powered with 3.3V?
Can't find it in the datasheet. High level threshold will be 0.7*VDD right? 0.7 ...
