to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
With NCS v3.1.0 and Nordic's downstream zephyr ncs-v3.1.0, I got build failure with following message:
--
warning: attempt to assign the value 'n' to the undefined...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi Support Team
Due to there is very little space of C: drive of computer, so I moved the NCS SDK from C: drive to D: drive. The VS code can't recognize the SDK and toolchain...
There are 100s of solutions on the zephyr git and the nordic git. It took me a while to understand it all and it took me hours of debugging and frustration before I ended...
I want to work with the nRF Connect Plugin for VS Code and my nRF52840 DK with Zephyr. I created a new application from the "nRF Connect" plugin and selected the hello world...
Hello,
I perform a test using a nrf52840 DK board in order to output a PWM at 50 Hz on a GPIO.
Here is the code:
void pwm_init(void) { nrf_drv_pwm_config_t const config0...
Dear Nordic-Support,
have a question regarding nrfutil and the offline package generation, described here: https://docs.nordicsemi.com/bundle/nrfutil/page/guides/installing...
I am evaluating Curve25519 performance on the nRF5340 and have observed that the following operations each require approximately 2.5 seconds to execute:
- `wc_curve25519_make_key...
My customer had ttothis question:
We recently purchased and use your Nordic Power Profiler PPK2 at my company. Does this device come with any calibration certificates? How...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hi all,
I was busy extending the asset tracker project and all of a sudden I got this lte rejection. First I thought maybe it the data limit has reached on the conexa sim...
Hello,
I've been having some connectivity issues w/ a multi-role application I'm working on. Essentially, whenever advertising is enabled, I am not able to establish a central...
I build code with the command
west build -b nrf52840dongle_nrf52840 and it builds fine, but I get errors when trying to Open DFU Bootloader E3FE4EE06DC5 with Programmer...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
Hello,
We are working with the nRF5340DK using nRF Connect SDK v2.9.1. Our firmware targets the nrf5340dk_nrf5340_cpuapp_ns board.
We would like to use P0.02 and P0.03...
