Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello, I attempted to enable the zephyr task watchdog model but whenever I configure it to enable the hardware watchdog module I get the error above. Any idea why I am getting...
Board: NRF52840
SDK: 16
Soft Device: s113
So our board is custom and does not contain a crystal. We are treating P0.00 and P0.01 as GPIOs for button inputs. P0.01 works...
Hi all,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
Using SDK15.3 on 52840. I've got a UART set up talking to something at 9600 baud..
The short course here is that imediately after init, I get an IRQ with a NRF_SERIAL_EVENT_DRV_ERR...
Hello, I´m working on my audio project and I try to stream some audio data (currently a 1 kHz square wave signal with 3.3 V peak) over I2S. The audio signal is sampled by...
Hello, I tried to implement the zephyr executing time functions API on my nrf52 hardware and I got the above error. According to my SoC documentation (nRF52833), this hardware...
Dear Devzone:
I am developing the design of a PCB that implements the nRF9160 SiP module, I have doubts about how to make the communication interface to connect the module...
Hello,
I used the nRF Connect plugin for VCS to create a Zephyr/BLE project. It appears this copies many files into the "build" directory which are required to compile the...
I am getting compilation errors when using the DT_ macros to access SPI bus child entries.
Overlay file:
&spi1 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin...
hardware : nRF52840DK-52840
SDK : NCSV1.7.1
IDE:Visual Studio Code
I wanted to printf float value , so I set CONFIG_CBPRINTF_FB_SUPPORT=y in my prj.conf file, my application...
Hello,
I'm using following code to read ADC values. The minimum sampling time I'm able to read the ADC reliably is 60ms. I want to lower it to say 5ms or 10ms.
Is there...
To the kind attention of Nordic support team,
reading at this: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrfxlib/softdevice_controller/README.html#softdevice...
Hello,
I have I am trying out the LPN sample from nRF5 SDK for Mesh v5.0.0 and I have an issue where certain mesh configuration messages (e.g. set publication, add application...
Hi, We have custom nrf52840/33 peripherals, advertising every couple hours, and passing/receiving information from centrals running node.js version 12.22.5 with pc-ble-driver...
