Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
Hi,
I was evaluating 9160DK. I tried the GPS example using 1.7.1 SDK and it works great outdoor. However, I tried to use a hackRF one to emulate the GPS signal. 9160 shows...
Hi
I still have a number of devices that are based on nRF24E1. From time to time the chips need a change in firmware. Since the last time I updated them, my PC has crashed...
Hi support team
I have been modifying the throughput example (nRF5 SDK v17) to connect the receiving unit (AMT client) to more than one device. I am running this on the...
Good day
I have Ubuntu 20.04.3 LTS installed on my laptop + fresh installation ( ~/.nrfconnect-apps was cleared and app reinstalled ) of nRF Connect 3.9.1
I use Bluetooth...
Hello!
My steps:
1 - Full working dfu over ble on nrf52840-dk + nrfutil + nrf52840 Dongle
2 - Change transport BLE -> ANT + nrfutil + ANT USB Stick 2, ANT USB(two different...
I am new in nrf52832 field i am trying to send some customized data(scan response) in ibeacon format of advertising. suggest me some ways or code to do the same
Thankyou...
Hi,
I have a custom EVB from Taiyo (EYSPBNZUA), https://www.yuden.co.jp/jp/product/category/module/img/TY_BLE_EYSPBNZUA_DataReport_V1_0_20201019E.pdf
When I press the...
Using above strategy for frequency measurement. Frequency source connected with one gpio pin.
Only GPIOTE PPI Timer modules are involved
HFXO is in use full time through...
I recently installed nrf connect sdk manually on windows 10.I found that i am able to open sample projects in segger embedded studio but not able to open our developed project...
Hi, everyone
I'm developing nRF52832 S132 with SDK 17.0.x
I wanted to change MTU size to 247 using 2 peripheral link in ble_app_multiperipheral example.
but i...
Hi Sir/Miss,
I try to implement static passkey in my project. Which is using nRF52810.
The SDK version is 17.0.2.
Softdevice is S112.
My project is based to develop...
