Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello, We're about to start a new project with the nrf5340 as our SoC. When reading the docs for the nrf5340 ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I have problem with wakeup of Low Power Node from System ON sleep mode. In debug session code works as expected, however outside the session something gets wrong.
The node...
Hi,
I'm trying to create an application based on the SMP Server app (NCS v1.7.0). I'm able to perform a FOTA using nRF Connect for Mobile and the app._update.bin without...
Hi,
I use the ble-app-uart-c-multilink example with a nRF52840 DK and 5 custom nRF52840 peripheral devices.
For a test, I want to connect to only one of those peripherals...
I am a newbie in nrF52832. I have been carrying some experiments using the Nrf51 and so far they are going so well. However, I came across some few E104-BT5052 samples originating...
In ncs1.7.1, I’m struggling with a problem about hard fault on nRF9160, but I have no idea to slove the problem.
nRF52840 transmits data to nRF9160 via UART0, the baudrate...
Hi,
I got the example http://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role and the demo is OK.
I also use nRF Connect APP to connect the ble_aggregator,...
Hi,
Hope you are doing good.
I run the SAADC signal to from the sdk and observed that when the adc input is connected to ground, the adc reads few random negative value...
Using nRF9160, ncs 1.6 on a custom board and segger-SES for debugging, we have intermittent stops (debugger breaks) on an assembler line with 'cpsie' opcode:
File: cpu_idle...
Hello Nordic support,
I am using nRF5 SDK for a Zigbee coordinator application. In zboss_api.h, I see that there are functions for setting short pan id (zb_set_pan_id()...
Hi, I'm starting a new custom development, that will use NRF52805 SOC. The project will be one Alexa Gadget device. I have seen several documentations, but I have some question...
Hi,
I have met one bug.
when I flash a fw with generic level server , then flash other fw with sensor server , the system runs error, if I use command "nrfjprog --eraseall...
Hi Nordic,
I have written a device driver following the guide as Devicetree HOWTOs , and try to call the driver api in main(), but got unexpected output as below.
I...
Hi nrf masters!
We have a problem quite late in a large development project and urgently need assistants. We have spent hour's reading all posts about this and debugging...
