Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hey, Our custom board based on the reference circuitry in " Product Specification v1.2 ":
We have been using the B0 revision of nRF9160 so far. Now we are planning on switching...
app_twi_perform() returns 0x03 == NRF_ERROR_INTERNAL.
Reset board with button does not help.
After Power Cycle can update EEPROM successfully.
Accessing FTM buffer with...
Hi,
we have developed our working UART code according to Zephyr documentation, and its working fine,
we find that this code works with EasyDMA . but my question is my...
I am trying to scan for Bluetooth LE devices in Android with Java. Everything worked fine and I released an update and on fresh installs it does not work. I went through every...
I'm seeing an assertion failure at PC=0xa806 in nrf52840 + S140 7.3.0, while using L2CAP.
I know the most common cause for softdevice assertion failures is interrupt/timing...
Hi, I'm using nRF52805 and SEGGER. My BLE device disconnects with the mobile app occasionally. The disconnection happens randomly. In the debug mode, I see some messages....
hi,guys
I have a product that uses CHIP 52832qfaae0, and then I replaced chip 52832qfaae1, and there is A problem. Chip 52832qfaae0 runs normally with the same code, but...
Hello,
looking at the compatibility matrix for the 820 it seems that rev2 of the 820 can be used with softdevices and the legacy SDK v17, while rev3 can only be used with...
Dear Members,
I want to use SPI LCD and Sdcard, they have different CS, but sharing the same SPI ports, I have used different SPI instance but not giving us a good response...
On opening a sample project located at https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with keil V5 , I can directly have an error message “Cannot read RTE...
Hi there, I'd like to make some FIR or IIR filter on my nRF52840 DK. I guess I'm supposed to: 1) Provide .a file into SES project's tree (or as Additional Input File): 2)...
I am working on OTA update .
Right now i am working simple
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hi,
Is there any command for reading the type of Nordic SoCs (e.g, nRF52833 or nRF52840) that is going to be programmed by nrfjprog/ J-Link Commander?
Thank you!
Hi Nordic,
I want to write a value from the application layer to the bootloader flash region through uart, and use this value to replace the button 4's function of entering...
