Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
After updating NRF Connect v3.9.0 to eliminate the recently documented JSON + connectivity errors with nrf Programmer and Power Profiler, my bash scripts utilizing nrfprog...
Hi，
1. Please provide me with an example of BMA280
2. The SDK: replication v1.7.1
3.IC:nRF9160
4. I tried to change the BME280 driver to BMA280 driver, but the following...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
Dear sir/madame,
By an accident I selected Power Profiler Kit II when I wanted to download an application to “PCA10056 DK” . After that ‘download’ Power Profiler Kit II...
Hello,
I'm using NRF52832 as a controller for cellular modem and used the AWS IOT supplied with the NRF Connect SDK.
I want to use the AWS FOTA and I'm a bit lost, I added...
This builds on a previous Forum Post that was closed out.
There is a peculiar issue with the NRF52840 SAADC sampling. For an unknown reason, triggering the SAMPLE Task in...
I have a nRF5340 with a UART that connects to a circuit that is not powered on until it is needed by the application. So the UART must be powered off until the application...
Hi,
We are developing cycling trainer, so we use BLE fitness machine profile. Our functions are basically completed and we are testing with some VR cycling windows or desktop...
Hello, please help if you can.
Once connected. I am asked to program the board when trying to use BLE from nerf connect.
However, I get the error: Error while setting...
Hi All,
According to the title,how should i do?
I want the project on the left to have a dependencies under main like the project on the right.
Best regards,
...
