Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I was looking to use the NUS Central project and port it to the PCA10059 (nrf52840 Dongle)
I was going to add the USBD_CDC_ACM so I can port the NUS traffic to a Putty terminal...
Hi,
i have nRF52840 DK.
I am working on radio test code based radio_test example code with nRF5_SDK_17.0.2_d674dde version.
If the transmitter is configured as : (BLEN...
I can't build examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay. I get the following error message:
cc1: fatal error: cannot open 'C:/.../examples...
Hello,
After looking at aws_iot sample files, I've stumbled upon the question regarding how one can dynamically change IDs and certificates for multiple 9160 devices? I...
From yesterdays question https://devzone.nordicsemi.com/f/nordic-q-a/80411/state-of-cs-ss-pin-after-nrfx_spim_xfer I have done a logic measurement and I can confirm that after...
Hi,
schematic for CFAA WLCSP mentioned, QDAA is given in the documentation. I want a reference for Circuit configuration no. 1 schematic for CFAA WLCSP mentioned in the...
Hi
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are trying...
Hello!
I am using nRF52-DK to deploy my programs. I try to use writing to SD card in ble_app_uart_central example. Both fatfs and ble_app_uart (central) examples work...
What are the memory settings in the SES compiler to compile secure_bootloader_ble_s140_pca10056
When I try to merge:
mergehex --merge s140_nrf52_7.2.0_softdevice.hex target_application...
I want to write some values to flash before the watchdog resets. For this I have the watchdog event handler specified:
In the wft_event_handler function I write a struct...
When trying to generate a new project Segger Project for my Project
in the option "Extra CMake Build Options" want to pass something like -DCONF_FILE='prj_test.conf' -DDTC_OVERLAY_FILE...
Hi Nordic team,
Looks like the most recent nrfjprog now supports flashing modem firmware.
I tried it and got some errors. Could you please point me in the right direction...
Dear Nordic Team Support
We face an issue where on different computers, using the same setup, different throughput can be achieved.
Setup:
- Custom Device using the...
Hello community...
I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful.
However, the...
