Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi,
I need help to clarify the API for IAS zone server. If I can get example implementation, it would be great.
I have hard time understanding how zb_ias_zone_app_callback_t...
Hi,
I am new to nRF9160DK . I want to set RTC time for the nRF9160DK.
In the application we are getting UTC time from NTP server and we need to set RTC .
I have referred...
Hello,
I am trying to get my nRF9160 to connect to a https server via AT commands, but this is as far as I've been able to get.
In the end this will be used in a project...
Custom board, ncs v1.5.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to a private...
Hi guys, I'm struggling on multiple fronts to make the system building up again after NCS upgrade to 1.5.0. This is the last uncanny warning I get at build time. Please give...
Using SD S140 7.2.0 SDK 17 (nRF52840).
I cannot write to internal flash addresses above 0x78000.
I am calling nrf_fstorage_init setting start_addr=0x68000 and end_addr...
Hello,
I am looking at the TX start-up current for the nRF5340 mentioned here (last 2 entries in the Radio current consumption (Transmitter) table) in the product specification...
Hello,
I am having an issue where I am trying to send a payload in the ACK in the ESB protocol. The issue is when the PRX gets a payload it was not expecting (i.e anything...
Hi Nordic team,
Please guide to resolve the error .
While trying to convert the model_handler.c to model_handler.cpp the below deceleration shows multiple compilation...
Summary: What are advantage bullet factors of Zephyr RTOS over FreeRTOS to choose this in nRF Connect SDK v1.5.0
Details: We have Implemented our previous project...
Due to a particularly stupid thing I have done on another chip, I have ended up depending on the ability to advertise a short name and a long name. However, when I build an...
I'm new to using micro controllers and for a project i have the nRF52 controller and i am trying to perform an OTA FW update using web bluetooth. When i connect to the board...
The problem is I can't figure out a way to use the shield pins on the board (P20) to program an external MCU (nrf52832). It just refuses to do so it always programs the onboard...
Hi,
We are using I2C to communicate with a sensor from the thingy:91. The sensor need either 3.3 V or 5 V I/O voltage levels to communicate.
As we understand it, the...
Hi all,
I am trying to develop a simple windows application using pc-ble-driver writing my own C# bindings on a nrf52840 dongle with nrf-ble-driver-sd_api_v6-mt-4_1_4.dll...
