to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi
I have a new Thingy:91 that I'm updating.
After I updated the modem software and the firmware with Connect desktop Programmer.
When i could not connect I deleted...
We recently had an issue where a race-condition was caused because we handled entry to sleep mode a bit too carefully. Therefore, I wanted to discuss different methods to...
Hello!
USing help from this forum i have successfullz transmitted adc value from one pin of AIN# to ble and reasing values successfullz but now i am facing an issue that...
Hi Nordic Team：
I use version is: nRF52840 DK Version：nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\ncp\ftd\uart\hex
Raspberry Pi 3 Version：RaspPi_OT_Border_Router_Demo_v4...
I am new to nrf52.
I want to configure TIMER1 as a counter.
However it does not count. I have added it after advertisement_init
Does the nrf52 have any such limitations...
Hii nordic;
I need to encrypt and decrypt my advertising data i.e;UUID,Major,Minor,etc.; of my nrf52832
So it cannot be seen by third parties
my sdk version is 15...
While trying to communicate through I2C/TWI with a MCP39F521 using a NRF52 DK (NRF52832), the first bit of the received data is always 1. The NRF52 DK is the TWI Master and...
Hi, I'm newbie to nRF DKs but started trying to run examples from pc-ble-driver-py / pc_ble_driver_py / examples / on github in order to get familiar with the nRF52840. I...
Hello
I'm setting up a set of Thingy91 and Thing52 units.
1) I registered 2 thingy91 sim cards and registered the nodes. 2) I see the SIM card in my account on nrfcloud...
I'm using a nRF52480 DK board with an adafruit 3421 I2S microphone breakout board attached. I am on Ubuntu 20.04 with SES 5.42c and SDK 16.
I am using a variant of the usbd_cdc_acm...
Hi,all
I am developing a Bluetooth product with HID function.I refer to the official keyboard example.I modified the "report_map_data" to implement some special keystrokes...
Hi Nordics,
we would like to evaluate the possibility of using NVM to store user settings. Based on the following searches, we still have some queries.
infocenter.nordicsemi...
Hello there, I just want to try a simple Ping test for at example 'google.com' with the nRF9160. Is there any easy way to try it? Or to try the internet connection in general...
Hi,
I wonder which setup that is best to begin with to develop wireless earbuds.
I'm looking at https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52840...
