In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Dear Nordic Team,
I am working on a product which implements OTA DFU(buttonless DFU inside). So far everything works fine and the updates are working.
The question is...
Hello,
I am using nRF52840 S140 V7.0.1. I am using ble_app_multirole_lesc example. I changed roles from “Central and Peripheral” to “Observer and Broadcater”.
My understanding...
Hi
nRF52840 SWD is push pull or open drain type?
And we want add level shifter between J-Link and nRF52840, do you have recommend level shifter PN? Or what type of level...
Current latest JLink firmware won't allow PPK working with DK RTT debugging.
The cause is the JLink chip on the DUT board won't put the SH_SWO/SH_SWCLK/SH_SWDIO in hi-Z...
I am working with the chip ISP4520 which combine Nordik NRF52832 and LORA semtech. I use nORDIC sdk 14. I burn the FW to the chip using Nordic development kit connected by...
Hi,
I tried a light-switch example from SDK for mesh ver 4.1.0 on two nRF52840 DKs(first board with client and the second with server). I configured them with nRF Mesh app...
Hi,
I have an unkown problem in my nrf52 application. It happens rarely, so I have no idea where to look at the moment. The only thing I know is that the WDT works and resets...
I have browsed through the forum and i couldn't find a similar question, so here I ask :
I have an application running a modified example of the Mesh Client & Server merged...
Hello there,
I'm trying to use my NRF51822 custom board as spi slave with BLE that sending whatever received from the master. I'm using MSP430FR5994 as the master.
I...
Dear Nordic,
I'm new in Bluetooth mesh and Nordic SoC.
I want to develop network of measure devices connected to each other using Bluetooth mesh. All devices need to report...
Hi all,
I installed this app on my nrf52832 DK and it works great. I'm totally newbie with Nordic and its hardware so i can't figure out how to adjust this code so the app...
Hello,
we are upgrading our application firmware to the v1.3.0 of nrf-sdk. We have now encountered a problem in which the build process just freezes/stops without exiting...
I try to build and run a "blinky" example for nRF52840 DK and nRF5340 PDK. And in the case of nRF52840 DK everything works properly. I connected to the boards and saw UART...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi,
I have a topology which has 20 to 50 nodes and these nodes should send a data packet of approximately 20 bytes at 50 Hz to a single gateway node. Is BLE mesh suitable...
