Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi, I was hoping someone could tell me if/when a version of the nRF Mesh Android App found here:
https://www.nordicsemi.com/eng/Products/Nordic-mobile-Apps/nRF-Mesh
Will...
Hi,
I'm using NRF52840 sdk v15 with Softdevice.
I have multiple SPIM instances and I make sure they are never active at the same time.
Can I share the pins (except the...
Hi, I'm trying to rate nrf52832 with stack ble_app_uart softdevice. My IDE is the IAR workbench for ARM 7.80.4. I downloaded the latest version nRF 5_SDK_15.0.0_a53641a, which...
Hi:
I would really, really, love it if you could provide a Segger SDK for Thingy! I've seen a few threads in here about the work to do it and it's a struggle. I noticed...
Hi there,
I've been searching around this forum for a while and still haven't gotten any reliable answer. I'm trying to develop a OTA firmware upgrade solution for the ATMega328p...
Hi:
when I compile project Thingy_ndoe in solution Thingy_node_s132_pca20020, an error meet,
C:\Nordic\thingy_sdk_v2.1.0\mesh_sdk\mesh\access\src\nrf_mesh_node_config...
I have combined the light switch server and client model to build control model. When i start provisioning for control model opcode status field : 2 error occurs which means...
Hi ,
I search nrf52810_bitfields.h , but i don't find about start bit , is the direction search for error ?
My idea : This is set up for stop bit , should the start bit...
Hi All,
I have serious difficulties to work with this board. I'm a beginners and I did not find any tutorial where I could said...oooh great I understood. My goal is to...
Hello all, I am trying to write a program that that updates the firmware on an external chip from a smartphone over BLE. Currently my approach is working but quite slow and...
Hello,
I am using a nrf52840 DK and I have no issues connecting to nrf connect. However, when it's connected all LEDs turn off and whatever code that was inside stops functioning...
Hi
I am programming NRF-51 board using nrfgo studio, it was working fine previously but now it failed to detect the board showing error. I shared screenshot of nrfgo studio...
Hello everybody,
I have integrated the new S140-SD-v6 Stack 6.10 into the github.com/.../nrf52-ble-app-uart-long-range Example.
It built and compiled without any errors...
Hello,
I want to get the raw acceleration of the Thingy 52. however I can't understand the values I get from the raw acceleration. What is the unit used for raw acceleration...
I am using Nordic SDK 13.0.0 with PCA 10040 dev board.
I have configured the stack to use MAX_BLE_MTU_SIZE = 200
// Configure maximum size of ATT packet the SoftDevice...
