Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
Howdy,
I am using an nRF52840 to perform BLE communication. For this communication I am using extended advertising to perform most of my data transmission. Thing is though...
Hello, i have a device supporting DFU OTA i'd like to create a small tool for flashing firmware from the computer to the device. I've set thr device to DFU mode. Is it possible...
I just got a PPK2. I was able to use it perfectly with Power Profiler. Great tool! Today I wanted to learn more about nRF Connect other applications. (Actually I was looking...
Hi there, I'm having so much trouble trying to get this two nRF9161 DK to communicate using SPI, being one Master and the other one Slave. I'm using the spi3 driver for SPI...
We had three nRF52840DK boards (PCA10056) for several years for use in development. Then one died (or to be fair, I killed it), so we got two more that turned out to be newer...
While using nRF Connect, I encountered an error when attempting to enter Debug mode with RTT active. Here are my J-Link specifications and log details:
When I have...
Hi folks,
I am using zephyr sdk version 2.7.0 with a custom board that integrates a nrf52832, an ens210 sensor for temperature and humidity and lis3dh sensor for accelerations...
Hello,
using nrf5340 audio sample present in SDK v2.9.0, I can't hear anything from my nrf5340 Audio DK
I'm testing unicast_server scenario using a Motorola Edge 50 Pro...
I would like to know how efficient it is in terms of power to use UART via the async UART API. Does power consumption differ when its receiving data vs when it is idle? Also...
Hi,
I'm required by FDA regulation to have an SBOM for my project,
I found online that Nordic supports a sort of software bill of materials in the following link: Software...
Im using two Thingy:91 X, Toolchain is v2.9.0. I build and flash the dect shell example. I select build configuration thingy91x/nrf9151/ns. No other changes.
Both devices...
Hello,
Currently i would like to test my modem on TX continuous wave mode, for LTE-M. I'm using dev kit nrf9160dk, modem firmware version v1.3.6 and nrf SDK v2.7.0.
...
