I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi All,
I am facing a strange problem. The scenario is that nRF51822 is acting as SPI SLave while MSP430 is acting as SPI Master. Using the SPI slave example as an app...
Hi all,
These steps broke my j-link lite! Is there a way to un-break it? Suggestions welcome.
I updated the segger pc software for another non nRF51 project (using a...
hi, nordic staff.
i'm working at s110(v6.0.0) and s120(v1.0.0). s110 provides notification and indication.
when s120 receives indication value from s110, s120 returns...
Hello all,
I successfully compiled and tested several examples for the nRF51822 Evaluation Kit on my Linux Box using gcc.
To do the same with my Smart Beacon Kit I downloaded...
I am trying DFU to work with gcc and SoftDevice 7.1.
Problem :
MCP able to send the APP binary successfully to the bootloader and DFU bootloader correctly write the app...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi, guys. Now I check the nRF51 IoT SDK(6lowpan, ipv6 over bluetooth).
nRF51 IoT SDK is needed Raspberry Pi, so I make the VMware Player Image for
Ubuntu 14.04.1 LTS 64bit...
I have a nRF51-DK. I would like to control the nRF51-DK through my mobile device.
What is the max. distance which can be reach with BLE(nordic chip)?
Is it possible...
Our application uses the S120 stack, and a bootloader. We want the bootloader to be able to update both our application software and the S120 stack (preserving the MBR). ...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
