Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hi All,
I am trying to print out floating values for my NRF5340 v2.4.1 SDK project. But, I am not able to print out the floating values. I tried the setting the following...
Hi,
Form the past few days, I've been trying to modify the device tree, but the changes are not reflected in the visual device tree. I’ve tried this on different laptops...
I have the following setup in my overlay file:
relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
Hi All,
I am using ' NRF SDK v2.7 + NRF5340 DK + VSCode ' and cloned a official nrf ' blinky ' sample. The code and pins are working fine and I have verified using DK...
Hello,
I can retrieve the data from the Thingy:53 via the bme68x_iaq program. However, I don't know and I can't read the data via BLE on my phone via nRF Connect. Do you...
Hi everyone,
I'm encountering a usage fault on the nRF52840 Featherboard when trying to connect to a network using OpenThread. The issue arises specifically during the execution...
Hi,
I am using the Create a new board function to specify a simple nRF52840 based board with GPIOs using nRF Connect SDK v2.8.0. No matter how I answer the questions in...
I'm using the nRF21540 DK with the Power Profiler Kit II in ampere mode for measuring current draw. I had the gain set to +20 dBm for testing but I noticed the system was...
Hi,
We have five NRF5340DKs with us and off late it seems three of them does not get detected by the PC. In fact, what i understand is that the interface MCU seems to be...
Thingy:91X rev 1.0.0
NCS 2.6.2 own custom application
Quiescent current measured with PPK II and extension board:
nRF53x 2µA, OK
nRF70x 0µA, OK
nRF91x 17µA, OK ...
Hello,
We are in the feasibility phase of updating a product to include a nRF9151 modem connected to a nRF52840 via a single UART. The modem will operate in SLM (Serial...
Hi,
Today the nRF Connect extension isn't working anymore: it doesn't show or let me select an SDK or toolchain.
I have tried on 2 separate computers where it was still...
I am using the latest (I believe) nRF Connect for VS Code extension, version 2024.12.55. But when I "Create a new application" and pick the ncs-example-application, it only...
Our nRF5340 application requires a lot of serial ports, but 2 of them are only used for a second during configuration and are otherwise (99.9% of the time) idle. If we could...
I am a complete newby to Nordic parts and the VB design environment so please bear with my ignorance. I have just purchased a nrf52840 development kit and have successfully...
