Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hello,
I would like to know if using a self made GATT Custom Service in HID Device (NRF Desktop App) can incur additional costs during the Bluetooth qualification process...
Hi,
I am working on a project using the nrf52840. For legacy reasons we are using Nordic SDK version 15.3.0 and SoftDevice S140 version 6.1.1.
I am trying to maximise...
I need help . i am confused that if we send the audio data then it follow which of the following order ? input ->BLOCK ->FRAME->LC3CODEC->SDU->PDU OR input-> BLOCK->FRAME...
We need to establish connections to muliple of our products (they use nRF52832/nRF52840) parallel from our Android/iOS apps to send commands which are time critical (in relation...
Hi,
I am getting an error when trying to enable the Fast Pair (SDK 2.7.0) using the bt_fast_pair_enable() function.
I debugged this error and I saw that it's caused when...
Hi,
I am developing an application which needs a precise reference clock of 20ms. I have a 32MHz Xtal on the PCB with a tolerance of +-10ppm. To configure the device to...
Hi
I'm using nrf toolchain/sdk 2.5.2.
Got a strange problem with my QSPI NOR flash interface. when i run flash_erase i get error message "qspi_nor: Failed to schedule...
I am running a nrf5340 with zigbee as a coordinator, I observed after a while that battery life of my end devices don't last as expected. Then after debugging I found that...
Hi Team,
We are developing a custom board using nRF52840 SoC. We need the storage and handling of IC, reflow solder profile of IC and assembly instructions if any.
Regards...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
hardware:nrf5340+npm1300
software:ncs 2.5.1
hi professor,
If I just connect VBUS, The npm1300 will reset when I read bulk register. If I connect vbat and vbus, read...
In NRFX Oscillator header , accessing the function requires the preprocessor macro which in turn requires preprocessor conditional
The problem is that final conditional...
Hi, I am developing firmware for a project using a custom board with the nrf52832. The project requires mcuboot and secure BT OTA. When I enable the configs
CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I'm trying to send gyro and acceleration values continuously using MPU6050(IMU) sensor through BLE after BLE connection is made with other device.
I took ble_app_uart...
I have a few questions regarding the power consumption calculation of the network and application cores from the 5340:
With the assumption that all peripherals are turned...
