I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
I have a nrf52820 on a pcb without 32Mhz crystal. I am using nrf52833DK to flash the nrf52820 on the pcb using debug out port on DK. I am able to see the connected device...
Hi, it's me, once again. Thankfully the last problem I had was actually my fault... I got distracted and didn't notice a small implementation detail... anyway... Here's today...
Hi,
The customer test routine serial_lte_modem mqtt returns 9,0
What does this state mean?
* ``9`` - Ping response from the MQTT broker.
Thank you for all your...
Hi,
I'm getting the following error during migration from 2.0.0 to 2.1.0:
[505/551] Building CXX object CMakeFiles/app.dir/C_/ncs/v2.1.0/modules/lib/matter/src/app/util...
Hi all.
I'm trying to learn a bit more about the device overlays,
I'd like to know how I would access the "gpio-line-names" that I've specified in my overlay in my application...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
Hello,
I am currently having my product, which is based on the nrf52810 SOC, tested and certified. I have been told to set my device up to use the DTM firmware example in...
Hello everyone
I have a few questions about how the nrf chip works: - does nrf52 work by sending AT comman and we need an intermediate chip like pca10040 send AT command...
I am trying to modify the Zigbee light switch example to transmit commands to the first bound endpoint, rather than to a bulb address determined by the app logic:
ZB_ZCL_ON_OFF_SEND_REQ...
Hi,
I am testing GPIOTE interrupts on 833, and noticed the interrupt is not fired sometimes (randomly) on power up. The input level did change as measured but the interrupt...
In this commit https://github.com/nrfconnect/sdk-zephyr/commit/d4023b3c1b8c32d978299143125ce5543c9bc6bb and this conflicting commit https://github.com/nrfconnect/sdk-zephyr...
Hello,
I am trying to compile the zephyr/samples/subsys/display/lvgl.
I have the lv_conf.h enabled
I'm getting an error "No SOURCES given to Zephyr library: drivers_display...
I'm using Zephyr as packaged in NCS v2.0.2
I have a thread that is "event" driven.
My first implementation used "signals" (k_poll(), k_poll_signal_raise()) to trigger...
Hi, I've noticed much higher than expected power usage and I've narrowed it down to PWM. I need to be able to turn off the PWMs when they're not needed.
I use all 4 PWMs...
