I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
i2c_recover_bus is used to re-sync slave devices on the i2c bus when they may be out of sync due to a reboot or other event.
i2c_recover_bus is currently not causing the...
Hi,
I'm mid-way through designing a custom board using the nRF52840. As I am space and height constrained I need to use the Tag Connect style connector used on the nRF52840...
We want to be able to manually send Friendship requests from LPN or to change request interval runtime.
It was possible to send requests manually using nRF5 Mesh SDK, however...
Hi guys;
I try to read and write the data without connecting nRF52832 .is there possible to do? Then is it correct or not? if it's wrong means give me the possible solutions...
I have a DK board with nRF52832 that I've been using several months with no problems.
Today I wanted to try an experiment and did some modifications to the startup ASM...
Hi,
Our setup is a new design with SDK 17.1.0 and it is expected to support DFU over BLE. We are using the nRF52832 SoC.
I am trying to understand the role that is being...
Hi,
We are having an issue modifying the blinky_pwm example for our needs. We have made a devicetree overlay file setting the pwms of &pwm_led0 to 28 and pwm0's ch0-pin...
I would like to use nrfjprog to erase nRF52832 device. But it failed with "An unknown error". The nRF52832 device connect to laptop through J-Link USB interface.
D:\Nordic...
Agenda : Use crypto features like AES-CBC, AES-CCM, RSA, ECC, etc. in secure environment (i.e. trustzone with SPM). Also, to use HUK, KMU for secure key generation and storage...
Hi All, I am migrating some applications (each with multiple custom board) from nCS1.5.1 + nCS1.9.1 to nCS2.0.0 I also noticed that in nCS2.0.0 the build output folder is...
Hi,
Depending on how the nRF5 SDK is configured, the BLE address may change once in the bootloader (it's incremented). This happens in the gap_address_change() function...
Hi Everyone,
I am trying to do OTA on NRF52833. In my previous project I was able to do OTA on NRF52840. The memory requirements for the project were as follows:-
Memory...
Hi, I'm trying to configure my VScode project for the nrf5340dk using the nrfconnect sdk to be more version control friendly and require less interactions to set it up. I...
hi..... everyone
I want to send the data from one node to particular node and that same data should want to print in termite using uart . so i checked the ble_uart coexist...
Hi all,
I'm trying to use the nRF52840-DK board to interface with the MAX31865 RTD-to-Digital Converter. I've adapted the MAX31865 C++ library to C and replaced the Arduino...
