I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
I'm trying to follow this how to and unfortunately cannot make it past step one.
https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts...
Hi,
I have a central that uses PM to connect to some peripherals.
If I connect to a peer (connection handle 0), and disconnect this device (e.g. by shutting it off). I...
Hi Nordic team,
We have just received our PCB prototypes with nRF52840 chip. While testing BLE functionality we found that the BLE is very weak. The connection is lost within...
Hi,
I'm trying to evaluate nrf5340_audio, but I get a build error as below.
> Executing task: nRF Connect: Build: nrf5340_audio/build (active) <
Building nrf5340_audio...
I'm trying to receive an HTTP response of approximately 100KB using the nrf9160 modem. When the response size is small recv works fine. When response is large recv returns...
GReetings,
Having a hard time using nRF Connect v3.11.1 for Desktop freshly installed on a Windows based laptop (Windows 10 Family 21H2)
J-Link V7.58b was installed simultaneously...
Good morning!
I am testing an application on Visual Studio Code + nRF Connect. I have a crash:
<err> os: Faulting instruction address (r15/pc): 0x0002c064
How can...
I have code that looks something like this:
static void some_worker(struct k_work *work) { struct state *state = CONTAINER_OF(work, struct state, some_work); k_spinlock_key_t...
My DK is connected via USB to my PC.
Uptill tommorrow it was connected and today it is saying not connected.
How to fix this ? Not sure what happened.
See below:
Have been trying to run nRF9160 sample code, including LwM2M client, and at client (latest nRF9160 firmware 1.3.2, latest SDK and Link Monitor 2.0.1) but in LTE Link Monitor...
I am unable to properly erase UICR registers on network core.
flash_erase() function that I call before flash_write() doesn't take any effect.
Example: 1. Set UICR->CUSTOMER...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
In general, what are the steps to adding a device using GPIO pins.
My thoughts are to physically connect my peripheral to the board and configure the device tree using an...
HI,
I recently migrated my nrf52840 based devices to Thread and Zigbee SDK 4.2.0
I used to have a good power consumption around 100-150uA with zigbee enabled.
Since...
I'm considering using the NRF52840 for a device with infrared proximity sensors that requires 8 IR LEDs to be driven at around 14 mA successively (never more than one at a...
