Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
Hi everybody, i get this error on a nrf53 with hr_coded on network coded, and UART example modified with multilink and coded_phy, tested by me on an nrf52.
The issue is...
Hello,
I was trying to get a Thingy:91 to run asset_tracker_v2 with an external GPS antenna connected to the U.FL.
NCS 1.7.0.
Based on the Thingy:91, I was trying...
Hello,
I am currently developing an application using as template the ble_app_uart.
My application works fine so far but we would like to add as a feature the pairing...
Hi All,
I am trying to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial without pressing BUTTON 1 and RESET buttons in nrf52840...
Hello, I am using sample hello_world app in SES, in the main file of which there are two print statements as: During flashing and debugging on the board, execution enters...
Good day to you,
I cannot find any reference/documentation whatsoever that relates to the following type of code... 4 lines of example code is below (from this link https...
Hi All,
I am trying to do Device Firmware Update (DFU) with MCUBoot bootloader for nrf52840 DK and I am following this link https://devzone.nordicsemi.com/guides/nrf-connect...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I am reading and writing data using FDS. If you execute fds_record_update at that time, the error of...
Hello,
I'm using the off the shelf Asset Tracker V2 and the application is sending GPS position and other sensor measurement at every 2 minutes.
Is there a CONF to change...
Hello developers,
I saw the process of bluetooth scanning from nordic infocenter.
Scanning for advertisers performing legacy advertising
In this picture, I don't understand...
Hello,
I have an application that runs on a 9160 which uses mbedtls (via TFM) to connect to an AWS server. The application is using a CA that you folks have given me in...
Is there a way to change a build configuration after it was created?
I want to change the kconfig fragments it is calling, but I was no able too. I have to delete and create...
I am trying to test TLS communication between TCP server and client so, how I should generate the certificates and how to provision them in TCP server?
Can I use OpenSSL...
