Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Sometimes when I call sd_ble_gatts_hvx, it can take several ms to return. Most of the time it takes very little time (<1ms), but occassionally it takes up to 34ms, my connection...
Hi Nordic Team,
In my application, I'm trying to read 512 bytes of data continuously from the STM32 master device. nrf52840 acts as a slave device. Every time I receive...
I have a DK of nRF52840, which is from 2016, and want to use it to test the LE Coded broadcast.
But it seems that 2016 DK does not support it, so I want to replace the chip...
Hi
I am working on direction finding examples, based on CTE feature that is introduced in BLE v5..
I have build and run both "tx" and "rx" examples successfully as described...
I have developed two PCBs that each use the rRF52840 chipset in the form of the BL654 modules from Laird which include PCB antennas.
I based the software project on the...
Hello,
I am trying to transmit weight measurements via BLE from a nRF52840-DK to a proprietary app. I am able to successfully transmit the data to the nRF Connect app on...
Hello Tech Support Team,
We are looking for a solution that can support LE audio. We currently use CSR8675 to make a Bluetooth dongle.
In order to support LE Audio, we...
Hi,
I'm having some issues trying to install the additional python dependencies for both zephyr and nrf
but it's not really working
I'm using this version of python...
Hi Nordic Team,
We require to perform below BLE range test, for which i would like to know which firmware i can use for the same.
1) To configure one device as continuous...
Hi,
We are testing mass pairing on our windows machines, as we have seen problems with a high number of paired devices.
I am able to increment the mac address by using...
Hi,
A simple CMAKE question, somewhat regarding the zephyr build, but pretty essential for someone using JTAG to debug the application:
How does one disable optimization...
I need to make a reset of mesh device with clearing its configuration.
For this I tried to use model_config_file_clear() or mesh_stack_config_clear() functions.
However...
Hi,
How to enable fast mode for radio transmission and reception (I am using nRF5 SDK). These are the default examples and I can see that fast mode is not implemented: ...
Hello again,
I saw this Github 's post and I was wondering if is possible to use some of the libraries and drivers with nRF52811 and if so should I pay attention to some...
Hi,
Question:
In our project we need to drive some external components (High Side Drivers) via GPIO output.
In order switch on our “High Side Drivers” we need a voltage...
