Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I want to use nRF52840 USB dongle as mesh server device. I have tried several links but not success. Please provide me hex file so I can flash using nRF connect desktop app...
Is there a way only from the analog input where measure the battery voltage to distinguish that battery is charging?
I am short on IOs and will be quite a challenge to find...
Dear all: Recently, I was debugging nrf52805 by custom PCB, using sdk17.00, I enabled PWM, frequency of 4kHz, to drive 4kHz passive buzzer, encountered a problem: The buzzer...
Hi,
I'm having problem using SPIS on nrf9160. The data/clock from master looks clean on scope, but 91 is not receiving the data. Interestingly, when I connect a debugger...
Dear,
We would like to have a setup where we want to measure the current consumption of a battery-powered device with an NRF-52840 chip:
The battery is a Li-Ion one...
Hello together,
I am try to get the asset_trecker_v2 to work on my thingy 91. When reading the debug log in LTE Link Monitor I see the warning:
So I downloaded the latest...
Hello, the chip I use is nrf52810 QCAA, when I use j-flash lite to earse the whole chip, it success, then I program the flash_s112_nrf52_7.2.0_softdevice into the chip by...
I am trying to merge the following projects:
SDK versions: 17.0.2 and 5.0
I have taken the contents of the mesh example sensor/server and merged it into the ble_blinky_example...
I created .c file, and add a few TWI functions to it. However, when I run the code in segger, all functions in the .c file shows a "multiple definitions of xxxx" error (see...
Hi!
I am working on an AoA project and I am using nRF Connect SDK. For the transmitter part I saw that sample application is already written and for receiving part it is...
Hi,
Our entire board is running around a nRF52832. Recently it has been difficult to find some of these SOC. Is it safe to replace it with the nRF52811 without changing...
Hi,
I am trying to compile ble_advertising.c file for a specific application based on nrf52840 and I am getting the following error:
nRF5_SDK_15.3.0_59ac345/components...
I am working with an nRF52840 on a custom board. Our device has a number of sensor attached in various ways including spim, twim, uart. I've used the ble_app_blinky as a starting...
Hi Dev Team,
I am enhancing my Thingy91 application using the mqtt_simple sample and NCS v1.5.0. I am basically connecting to the MQTT broker, sending data and then disconnecting...
I am using nrf52840 as PTX and nrf24l01+ as PRX. The application I am working on requires me to send 30 bytes from PTX to PRX at a 2 kHz packet rate. If both devices are near...
