Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi All,
Currently in my project i'm using hard core delay and delay is custom i.e some places i have used millisecond and in some places used microsecond and in sec.But...
Hi all,
I may need some guidance on the finite state machine method which found an example in app_level.c (from nRF5 SDK for Mesh v3.1), please see my question on below...
What is the minimum specified voltage required on ENABLE (Pin 101) for proper operation of the nRF9160 SIP? Is it the traditional 0.7 VDD, or is it permissible to use a lower...
Hello, I work with an nRF52832 DK and I want to test the example code "ble_app_uart_coexist" . I use the S132 softdevice, SDK 15.3.0 and version 3.1.0 of the mesh for this...
Hi
I used the SDK14 with nRF52832, and carry out the blinky example. When using the Android, the BLE device could be found, but the IOS cannot scan the device. So could...
Hi,
So I am working on NRF52832 with S132 6.1.0 and SDK 15.2.0 mtu and data lenght testings. During that time I was unable to change mtu multiple times while connected ...
I have a ble device and want to write a byte array in nRF Master Control Panel. Firstly, it can be written. But i don't know ho w to input it. My byte array is [-128, -64...
Hi,
I looked at this comment.
If this function (sd_power_system_off) is executed, can I wake up the device again with a soft reset?
If not,
What is a function that...
Hi,
In the documentation nFR523832_PS_v1.4, on page 107, the registers HFCLKSTAT and LFCLKSTAT when in reset mode, indicates that the LFCLK is not runing, and neither the...
Hi Everyone
I am trying to use 2 instances of SPI SPI0 AND SPI2 for Epaper Display and MCP2515 CAN bus module respectively.
Epaper and CAN are working fine if one of them...
I am using NRF52 SDK version 15.3. I am using the app_usbd_cdc_acm module to create a virtual serial port between an NRF52840 DK and a Linux laptop. I am sending messages...
I'm looking into migrating my project from gcc/make to Segger Embedded Studio, because I have some tricky debugging to do and SES should be a bit easier to use than GDB for...
Hi all,
I use nRF52832-QFAA, S132 2.0.0, SDK 11.0.0, IAR 7.5, Windows
Upon connection, I am trying to resolve the peer "random private resolvable" address (not for whitelisting...
I have been having issues of when I operate some components in the system the nRF52832 goes into a hard reset. I have seemed to fix a lot of the hardware issues but there...
