Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I want to use UART.
I checked the waveform and UART does not send data. Here is my code. build and run are successful. Any help? I connect UART RX and TX directly, which...
hi... how to make a nordic app to act as a peripheral , i have read one post , in that they mentioned set up to be done in gap peripheral mode . how to do that
IAR 7.60
52840
nRF5_SDK_15.2.0_9412b96
Hi there, I'm trying to do some modification in the bootloader (so that we can write the image to the flash's bank1 using our...
Hello,
I read through the Bluetooth core specification in order to get a better understanding of the information that has to be stored at a minimum if using bonding. But...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
We are currently in the prototype stage using the nRF9160 and are preparing the firmware for the prototype. We have a few question that we hope someone could answer :)
Will...
Hi,
I want to test BLE 5.0 using two nRF52 dev kit. i am using the ble_app_uart example kindly guide me what are the changes to made in this example to connect two kits...
It's easy for me to create make file target but I am not able to identify where and how to add the custom target in the Segger Embedded Studio(SES).
My default build configuration...
Hi everyone. I am trying to find the best way to establish a Bluetooth connection to a nRF52832 in the least amount of time.
I'm designing an ultra low power perpheral...
Hello,
Would it be possible to create a partial code that can be placed on external memory, and loaded into ram for execution when needed?
As I believe it is possible...
Hi,
I am developing a Bluetooth peripheral application using NRF52832 MCU , where in it is used for collecting vibration sensor data for about specific duration.
like...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hello All,
I am new to Nordic and i have nRF52840 development kit. I want to build code/ programm on thread and Zigbee base.
I have downloaded the Thread and Zigbee SDK...
Hi!
I do not know what the problem is.
First of all, I use nrf52-dk and SDK 15.2
And then, i read 'PPK User Guide v2.3'
I use 'nRF Connect > Power Profiler' to measure...
