Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I choose one NRF52 DK(nrf52840_pca10056) for my daily development. After hundreds of erase and write cycles, the DK won't behaves like it should do. The other DKs runs well...
Hi,
In the registery definition of nRF52840 it is stated for PSEL.TXD:
Reg ID: A -> from bit 0 til 4 for Pin selection
Reg ID: B -> bit 5 for Port number
In this case...
I am looking into interfacing a SD card to the nRF52840. I have used the FatFS example and that is working ok with SPI. Then I have looked at the QSPI example and that also...
Hello,
I am using sdk 12.2 and nrf52 dk.
I am storing some data in flash using ( sd_flash_write((uint32_t*)0x4F800,m_deadbeef, sizeof(m_deadbeef));) and I am able...
Hi
I got the problem to connect customer board(nRF52) via SWD.
My connection should be fine and customer board is also supplied 3,3V by external power.
How I wire 52Dk...
Hi,
I want to add fstorage functionality to my applikation. I added all the files and functions as in the fstorage example from Nordic, but I get a linker error that the...
I am using an RTC to periodically kick off a PWM pulse train. This all works beautifully, but draws far more current than expected. From what I've read, this is because the...
Hi,
I've been working to get a Ublox GPS module to interface with my NRF52840 DK over UART. The GPS device boots up and starts streaming data almost immediately.
I am...
I am nRF52832 , S132 , SDK15.0.0 // nRF52840, SDK15.0.0 is used.
Examples of esb_prx, esb_ptx are modified and used.
Transmitter : nRF52832
Receive : nRF52840_DK
Senders...
hello
I have once again issues when I want to write a 'long" characteristic e.g. 85 bytes.
1) if I use a smaller MTU e.g. 23 or 50, I received corrtectly the User Memory...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
