I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
I am using nRF-Sniffer-v2.0.0.2 beta as seen here: https://www.nordicsemi.com/eng/nordic/Products/nRF-Sniffer/nRF-Sniffer-v2/65225 on a nRF52840 DK.
Wireshark Version: 2...
Hello guys,
I'm having problems with communication between a dwm1001 module (from Decawave) which is a nrf52832 board, and my Raspberry 3 Pi model B.
I have connected...
Hi
According to nRF52840 Product Specification, the SPI master data rate can be set in the SPI frequency register. The configurable values are listed there. Is it possible...
Hello everyone,
Maybe it is a stupid question but I am completely lost,
I have a stm32f103c8tb that I have to use for programming a nrf51822, the thing is I have absolutely...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE.
After pairing, the sum...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE. After pairing, the sum...
Hi
At the company I work for (Ztove ApS) we have expanded the capacity of nrfutil (https://github.com/NordicSemiconductor/pc-nrfutil) to include a option for AES (CBC mode...
Hi
In ESB there is the function nrf_esb_suspend(). After calling it, what function do I call to resume ?
Look forward to hearing from you
Regards
Mahendra
Hello!
Related to the addition of new services to the Attributes table, is there a way to check if a certain service UUID has already been added?
This problem arose because...
How do I check what version I have installed?
The 'Getting Started' page states a minimum version of 9 .5. 0:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
