I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi everyone!
During the development of our device, we faced with some problems:
So now we need to read the data array in a clear sequence from characteristics. The data...
Hi,
I have a device running firmware from SDK10 and using s110. I would like to update the device to use SDK11 firmware with S130v2. I'm using following code to generate...
Hello,
my application hex used to work fine before i change my bootloader and softdevice
now after falshing all the hex including the application , it is advertising as...
Hi,
I want data read from my sensor (gives continuous data when button is being pressed). and then send it through Bluetooth equipment.(PC or iPhone and so on) But i don...
nRF51_SDK_9.0.0_2e23562
S310
/*
* Setup the gpiote to handle pin events on the MMA8451Q INT1 pin. For the
* accelerometer we want to detect high->low transitions in...
hello everybody,
I'm working in a project & have to do something like security for the connection & be able to do updates to firmwares, someone suggested that doing bonding...
In past , I was able to perform DFU-OTA over BLE transport for a custom board that has nRF51822QFAA (256kB main flash memory) SOC. I tested this functionality with Nordic...
I am trying to setup a nRF51422 Development Kit (PCA10028) v1.1.0 board with ble-sniffer_win_1.0.1 sniffer. I programmed the Dev board with firmware version ble-sniffer_nRF51822_1...
Hi all,
I am using ble_app_uart application to send data to a Bluetooth device. I am sending the data to the Tx Rx Pins of nrF51822 module via an external controller. My...
Hello forum, I've been trying to get SOME alert on my nRF51DK from a phone. I first tried the alert_notification example, but it appears that one has to write a custom Android...
I'm trying to build the blinky example in SDK 11 and load it onto a PCA10000. I'm using the make file in PCA10031/blank/armgcc and am building this under linux. If I use blinky_blank_pca10031...
Hello All,
I am using nRF51822 with SDKv10.0.0 and s110 soft device with RTX os. My project have 5 different threads with 1000 bytes of memory is needed in each thread...
Hello,
I have a project where I wish to have BLE operation while active and use RTC1 as a calendar keeper while in low power mode. So far as I have seen, the softdevice...
Hi all,
I am currently working on the nRF51422 with the S110 version of the Softdevice. The SDK version is 8.1.0.
I tried to get some information back from the Softdevice...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels. since in hardware design, I have designed the chip with...
