Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi folks!
As always, I'll start with relevant environment details
===== Environment =====
nRF Connect SDK v2.5.0 (though not opposed to upgrading to one of the 2.6.X...
Hi,
We are developing a device using nRF5340+nRF7002 running Matter. The problem we have is the code size which is around 900KB when Matter is enabled. This leaves us with...
Hi,
My custom board nRF52840 works as a Peripheral, which advertises itself for connection from a Central.
The project is built based on peripheral_hr sample project....
Dear:
I can upgrade applicaiton ONLY sucessfully through DFU.
but now, i want to upgrade applicaiton+softdeivce+bootloader to deployed devices. do you have such documets...
Hi,
What is the maximum PWM frequency one can achieve on the nrf52840 with 50% duty cycle? Sample .dts and c-code in NRF Connect SDK would be appreciated!
In practice...
HI.
we're developing an application where we need to use 2 UART ports: UART: 0, 2, 3.
Before we added MCU boot in our project everything worked well but after we integrated...
I am working on nrf52832 based custom board and I want system off sleep and wakeup using GPIO pin state change. For that I have configured MCU standby timeout in sdk_config...
I have a thingy91 device and want to implement the following requirements.
Expectation:
NRF9160 should remain in deep sleep mode and on the button click event do the...
I am developing firmware for a BLE peripheral using ncs v2.6.1.
In addition to using the libraries introduced in nRF Connect SDK Fundamentals and BLE Fundamentals on DevAcademy...
Hi,
I am considering to build a line of products using the nRF 5340 product and I am considering the options to perform FOTA.
So far the option I learned from the Intermediate...
1. What could be the reason why streaming is not synchronized even though the connection is established?
2. Where in the source is the important information for connecting...
Hi there
I want to measure the accuracy of the 32.768 kHz oscillator connected to a nRF5340
I have tried a lot of other devzone tickets, but most of them are too old or...
Hi ,
nRF52832 using pairing connection with Android phone,after repeatedly disconnect and re-connect ,after several minutes will maybe make the phone's bondibng information...
Hi,
I have now sync the transmit of nrf IC to communicate with tas2781 audio amplifier. at this moment I'm working on the feedback measurement read of the I/V measurement...
Hello, nordic team
I have encountered unusually high power consumption in a simple GPIO edge interrupt application running on a custom nRF9160 board. The application is...
