At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi Nordic,
I am using your QSPI example code and make it into functions for my application. The code could run if I block the rest part of my code and only run the QSPI...
Hi,
4 years ago we implemented a 802.15.4 and Bluetooth Multi protocol project on the nrf52840. Our application continuously ran 802.15.4 and bluetooth was just used for...
i tried to use the high voltage mode of nrf52840, but when i flash a firmware called "ble_app_hids_keyboard" which use the nrf52 sdk, all is good. but when i flash the firmware...
Hi,
I'm using nRF9160dk to configure MQTT . i'm new to MQTT so ,Is their any example code to understand and work on it by using " ZEPHYR RTOS "
thanks in advance.
A product I'm working on uses an nRF5340 (actually a Fanstel BT40 module with an nRF5340 in it) with NCS v1.7.1.
It's got an SPI slave connection (the nRF is the slave)...
good day,
is there a guide or tutorial on how to detect different press type in single button? will try to assign different tasks per button press types (single, double...
Hi Support team,
According our spec 52832 rx is about 5.4mA, but actually i measured our example, it is about 7.1mA, may i ask where is the gap? so i suspect it is because...
Hi,
I'm developing an application based on the nRF52832 development kit. It is nrf52dk_nrf52832(PCA10040). I have used nRF Connect SDK (3.0.0) for the project development...
Hello,
I am trying to interface the ble_hid_keyboard with uart using nrf52840-Dk in SDK 17.0.2. But not able to print data from uart and even not able to connect hid keyboard...
Hi,
I have an nRF9160 and working am off of the AWS_IOT sample code. When I start the device, the error messages occur 2-3 times and then the device connects successfully...
Hi,
I'm working on a custom board with a nrf9160 µC. This board is powered by a battery and a supercapacitor and my job is to assure the autonomy of the battery.
I...
I am using 9160 to develop a product for customers, which saves the date, time and other settings in NVS. Yesterday, I encountered a problem that the product could not start...
Hi Nordic team,
Is there any sample project which implements DFU controller in nRF52832 central device? I need to update peripheral device firmware from central device...
We are using SDK 17.1.0 with SoC nRF52832 and Soft Device S132.
We want to configure the soft device to enable the TX and RX GPIOs to talk to off-chip power amplifier. Looks...
Hello there. I would like to know how can I read the counter value right before resetting WDT directly from the register.
That means right before calling:
I want to know...
