At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I tried to use printf() to get the data from SPI buffers. It runs OK in the peripheral/spi example. But when I moved it to the ble_app_uart, the program stalled at printf...
Hi,
We are looking to upgrade our connect SDK version to 1.7.1 (from 1.5.1) but at the moment there are a few breaking issues for us that will prevent us from doing so....
Hi All,
I have a question that i remark this code run different mode have different results
in Release mode => build success,the project can run
in Debug mode => the...
Hello.
I have couple of questions for hardware parts location on pcb with nRF9160.
Q1.
I'd like to ask a better location for eSIM(MFF2) related nRF9150.
This...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
In an effort to fix Toolchain problems setting up nRF Connect, I uninstalled Python and tried reinstalling via choco install python as per the "Installing Manually" instructions...
Hi,
Please fix this bug: The DK device is no longer found after following the following procedure
Problem operation process emerges
windows:
DK:PCA10090 0.9...
Hello,
I started my prototyping with the 52840DK and the SD Card was working fine. However, with the 5340 dev kit, I cannot get the SPI to work and access the SD Card properly...
Hi,
I connected my nRF52840 dongle to the laptop, it was detected with a red LED glowing on and off. Later I installed the nRF Connect software and installed the Power...
In our nRF52832 application, we have an external 32.768KHz crystal as the nRF52832 low frequency clock source. We also have a 32.768KHz oscillator on the PCB that is used...
Hello,
There seems to be a bug with scanning for many Bluetooth advertisements while simultaneously sending data over uart in Nrf sdk v17.
I have tried to work around...
When loading the nRF Connect Plugin for VCS, I am receiving either a crash message or the message below. It looks like a Python syntax error in the kconfig extension. python...
SDK 17
Soft device 7.2.0
nRF52840
Started with the 'fatfs' example, updated it to allow uninit, and to not reinit the IO if init is called multiple times.
it's working...
Hello everyone, I combined work with a timer and an example from ble_app_aurt pca10040 s132, the problem is that the timer does not work evenly, yes, I know about the low...
