I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi Support Team,
What's the UBM pad diameter of nRF5340-CLAA?
BTW, any correlation between it and label 'b' in Mechanical specifications in PS?
Best regards
Sal...
When I try to open the .overlay file in SEGGER it shows me an error : "Can't Read file" with the message "Can't open xxxxxx/xxxxx/xxxx.overlay for reading.
Has anyone else...
Hi,
I am running Homekit over Thread sample(NCS/Homekit tag v1.7.0 using MTD-SED conf) on my custom board and I found that the QSPI Flash (MX25R64, as same as the one use...
I want to test OTA in button mode. I have configured the button in DFU project. Now I upload the files in my device in the following pattern:-
1)Bootloader hex file
2...
Hello,
I have an nrf5340-dk board and I am trying to play around with the different baud rates through changing the overlay file (as shown):
I am using teraterm...
Hi guys,
After weeks and weeks of trying with 3 different boards (Thingy91, nrf9160DK and Custom board), combination of different LTE Antennas, Bell, Hologram and iBasis...
I am using nrf52840's dongle development software, and I found that when the slave device sends LL_SLAVE_FEATURE_REQ , the host will return LL_UNKNOWN_RSP. I want to know...
Using the NRF connect app we can simulate the problem we have in our app Cowboy. Some customers cannot pair with the bike that uses the nRF52840. We have secure and non secure...
Hi, I am Marcous.
Currently I am doing multiple beacons (transmitters) in direction finding demos. Since I found that there is no way to simultaneously receive the CTE containing...
Hello there,
We are developing an application which inits all the peripherals and sleeps.
We are initializing:
GPIO's for waking up from interrupt
NFC also should...
Hello,
I am using NCS v1.6.0 for nRF52840.
I need to write 8210 bytes to flash via I2C. I configured the I2C0 with NRFX_TWIM and NRFX_TWIM0 enabled in the prj.conf file...
Bluetooth low energy, Direct Test mode nor RSSI Viewer is working with my nRF5340DK board. For instance with RSSI Viewer it says "Error while setting up device XXXXXXXXXXXX...
Hi
I need to build a communication between nrf5340 and esp32 using UART Protocol. I need to transfer some data from nrf5340 to esp32 and vice versa via UART. Already, I...
I want to add Service based on the Bluetooth base UUID which is 00000000-0000-1000-8000-00805F9B34FB When I am trying to add it using "sd_ble_uuid_vs_add", it always returns...
nrf52805 is being used as a GATT server using a static passkey. An ESP WROOM 32 is being used as a GATT CLIENT. The issues is that nrf52805 sends a disconnect to ESP32 after...
